ClearShield Hinged & Sliding Security Doors Spec.
Aluminium Framing
Grade: 6063- T6
Dimension: 75mm x 19mm Extruded Aluminium
Coating: If Anodised, minimum of 15um to A.S 3715
If Powder Coated, Chromate pre-treated and powder coated to A.S 3715.
Stainless Steel Sheet
Grade: T304
Finish: 2B
Construction: Flat ‘round holed’ perforations
Thickness: 0.8mm ‘Raw Un-Coated’
Hole Size: 1.8mm +/- 0.1mm ‘When Coated’
Spacing: 3.0mm
Pitch: 60 degrees staggered pitch
Retaining edge of sheet: 5mm x 90 degrees folded on all sides
Coating: Pre-treated with GB4520 chrome process and powder coated with Jotun polyester powder coating to a minimum of 70 microns.
Construction Specification
Corner Staking: Heavy duty aluminium extruded staking angle to be used with 4 x 6-4 aluminium rivets per corner.
Stainless Steel Sheet Retaining Method: Stainless Steel Sheet must be totally insulated from the aluminium frame and or any dissimilar metals using the ClearShield proprietary insulating membrane. Stainless Steel Sheet is to be retained securely inside the aluminium frame using the ClearShield wedge that retains the bent edge of the sheet within a zone in the aluminium frame.
Locking Mechanism
Three point locking system and three hinges must be used and installed as per the manufacturers A.S 5039 test report.
Performance
Infill must withstand 20 cycles the AS4483 Knife shear test without penetration greater than 150mm
Infill must withstand (50 impacts at 100j) as used in AS5041-2008 without infill retention failure.
Infill must withstand a minimum of 2,000hrs salt spray testing to AS4506-2005 with nil corrosion.
ClearShield Security Screen Spec.
Aluminium Framing
Grade: 6063- T6
Dimension: 33mm x 16mm Extruded Aluminium
Coating: If Anodised, minimum of 15um to A.S 3715
If Powder Coated, Chromate pre-treated and powder coated to A.S 3715.
Stainless Steel Sheet
Grade: T304
Finish: 2B
Construction: Flat ‘round holed’ perforations
Thickness: 0.8mm ‘Raw Un-Coated’
Hole Size: 1.8mm +/- 0.1mm ‘When Coated’
Spacing: 3.0mm
Pitch: 60 degrees staggered pitch
Retaining edge of sheet: 5mm x 90 degrees folded on all sides
Coating: Pre-treated with GB4520 chrome process and powder coated with Jotun polyester powder coating to a minimum of 70 microns.
Construction Specification
Corner Staking: Heavy duty aluminium extruded staking angle to be used with 4 x 1mm pneumatic stamping of corners.
Stainless Steel Sheet Retaining Method: Stainless Steel Sheet must be totally insulated from the aluminium frame and or any dissimilar metals using the ClearShield proprietary insulating membrane. Stainless Steel Sheet is to be retained securely inside the aluminium frame using the ClearShield wedge that retains the bent edge of the sheet within a zone in the aluminium frame.
Performance
Infill must withstand 20 cycles the AS4483 Knife shear test without penetration greater than 150mm
Infill must withstand (50 impacts at 100j) as used in AS5041-2008 without infill retention failure.
Infill must withstand a minimum of 2,000hrs salt spray testing to AS4506-2005 with nil corrosion.
ClearShield Emergency Exit Screen Spec.
Aluminium Framing
Grade: 6063- T6
Dimension: 52mm x 13mm Extruded Aluminium
Coating: If Anodised, minimum of 15um to A.S 3715
If Powder Coated, Chromate pre-treated and powder coated to A.S 3715.
Stainless Steel Sheet
Grade: T304
Finish: 2B
Construction: Flat ‘round holed’ perforations
Thickness: 0.8mm ‘Raw Un-Coated’
Hole Size: 1.8mm +/- 0.1mm ‘When Coated’
Spacing: 3.0mm
Pitch: 60 degrees staggered pitch
Retaining edge of sheet: 5mm x 90 degrees folded on all sides
Coating: Pre-treated with GB4520 chrome process and powder coated with Jotun polyester powder coating to a minimum of 70 microns.
Construction Specification
Corner Staking: Heavy duty aluminium extruded staking angle to be used with 4 x 1mm pneumatic stamping of corners.
Stainless Steel Sheet Retaining Method: Stainless Steel Sheet must be totally insulated from the aluminium frame and or any dissimilar metals using the ClearShield proprietary insulating membrane. Stainless Steel Sheet is to be retained securely inside the aluminium frame using the ClearShield wedge that retains the bent edge of the sheet within a zone in the aluminium frame.
Release Mechanism
Lock Mechanism must only be accessible from inside only.
Lock release mechanism must be continuous along the opening side of the screen.
Lock release mechanism must be clearly labelled ‘PUSH HERE’ near the lock mechanism.
Hinge mechanism must comprise of a continuous anti theft interlocking arrangement the screen sash interleaves with its mounting frame.
Performance
Infill must withstand 20 cycles the AS4483 Knife shear test without penetration greater than 150mm
Infill must withstand (50 impacts at 100j) as used in AS5041-2008 without infill retention failure.
Infill must withstand a minimum of 2,000hrs salt spray testing to AS4506-2005 with nil corrosion.
ClearShield Cyclone Rated Products Spec.
Aluminium Framing
Grade: 6063- T6
Dimension: Screens 52mm x 13mm, Doors 75 x 19mm Extruded Aluminium
Coating: If Anodised, minimum of 15um to A.S 3715
If Powder Coated, Chromate pre-treated and powder coated to A.S 3715.
Stainless Steel Sheet
Grade: T304
Finish: 2B
Construction: Flat ‘round holed’ perforations
Thickness: 1.5mm ‘Raw Un-Coated’
Hole Size: 1.8mm -2.4mm+/- 0.1mm ‘When Coated’
Spacing: 3.0-5.0mm
Pitch: 60 degrees staggered pitch
Retaining edge of sheet: 5mm x 90 degrees folded on all sides
Coating: Pre-treated with GB4520 chrome process and powder coated with Jotun polyester powder coating to a minimum of 70 microns.
Construction Specification
Corner Staking: Heavy duty aluminium extruded staking angle to be used with 4 x 1mm pneumatic stamping of corners.
Stainless Steel Sheet Retaining Method: Stainless Steel Sheet must be totally insulated from the aluminium frame and or any dissimilar metals using the ClearShield proprietary insulating membrane. Stainless Steel Sheet is to be retained securely inside the aluminium frame using the ClearShield wedge that retains the bent edge of the sheet within a zone in the aluminium frame.
Release Mechanism
Lock Mechanism must only be accessible from inside only and must be continuous along the opening side of the screen. Lock release mechanism must be clearly labelled ‘PUSH HERE’ near the lock mechanism.
Hinge mechanism must comprise of a continuous anti theft interlocking arrangement the screen sash interleaves with its mounting frame.
Performance
Screen must comply with AS1170.2.2011 for the specific level of requirements that relate to the location of the products end use.
Test certification of the supplied product is to include the following:
- NATA certified reports showing screens larger and smaller sized screens tested than those supplied.
- NATA reports must show impact resistance on all test samples both in the centre and edge of screens.